Raked glass panel dimensions calculator

Fence / Layout

Convert known raked-panel length and height bases into panel and rectangular blank dimensions for a fabricator.

Enter your inputs

A worked project example is loaded and calculated automatically. Replace the values with your project inputs.

Input notes

Enter known project dimensions and choose the measurement bases explicitly. Panel height perpendicular to the sloping top differs from the vertical end height. Bottom offset is the horizontal flat portion at the lower end. The blank rectangle is aligned with the sloping top; its length is not the panel's horizontal span. Send the dimensions to your fabricator for review. This tool does not authorize field cutting, select glass thickness or establish product/code suitability.

degrees
Enter slope angle in degrees.
Choose the option that matches your project.
in
Enter panel length in inches.
Choose the option that matches your project.
in
Enter panel height in inches.
in
Enter bottom offset in inches.

About this calculator

Raked-panel geometry converts a selected top-length and height basis into horizontal span, vertical end height, blank dimensions, and area.

Steps

  1. Slope angle

    Enter slope angle in degrees.

  2. Panel length basis

    Choose the option that matches your project.

  3. Panel length

    Enter panel length in inches.

  4. Panel height basis

    Choose the option that matches your project.

  5. Panel height

    Enter panel height in inches.

  6. Bottom offset

    Enter bottom offset in inches.

Formula

For angle θ, top length T and perpendicular height H: horizontal length = T cos θ; vertical end height = H ÷ cos θ. For horizontal bottom offset o: left end = H ÷ cos θ − o tan θ; blank length = T + (H − o sin θ) tan θ; panel area = T × H − o² tan θ ÷ 2. Divide square inches by 144 for square feet. Angle range 0–45° follows this declared source model.

Interpret the result

The blank is a rectangular fabrication envelope under the selected geometry. It is not a finished cut instruction or approval for field processing.

Worked example

At 36.8699°, cos θ is 0.8 and tan θ is 0.75. A 32-in perpendicular height gives 32 ÷ 0.8 = 40 in vertically; the blank length is 60 + 32 × 0.75 = 84 in.

Example result: 84 in blank length

Example inputs
Slope angle
36.86989764584402 degrees
Panel length basis
Length along sloping top
Panel length
60 in
Panel height basis
Perpendicular to sloping top
Panel height
32 in
Bottom offset
0 in

FAQs

Why are top length and horizontal length different?

Top length follows the sloped edge; horizontal length is its projection along the baseline at the entered angle.

What do the layout marks refer to?

Use the stated origin, centerline or face reference, and units shown with the result. Display rounding may differ from the internal coordinates.

Does this approve the selected dimensions or product?

No. It lays out the dimensions you enter and does not establish structural capacity, product cutting permission, or installation compliance.

Additional examples and limits

Raked panel dimension example

A slope of approximately 36.869897646° has cos θ = 0.8, sin θ = 0.6 and tan θ = 0.75. With a 60 in sloping top and 32 in perpendicular height, the horizontal span is 48 in and vertical end height is 40 in. The aligned rectangular blank is 84 × 32 in, or 18.667 sq ft; the panel area is 13.333 sq ft. Entering 48 in horizontal length and 40 in vertical height describes the same panel.

An 8 in horizontal bottom offset gives a 34 in left end, 50 in sloping lower edge and 80.4 in blank length. Panel area is (60 × 32 − 8² × 0.75 ÷ 2) ÷ 144 = 13.167 sq ft. End-and-notch edge length reports the two vertical ends and the horizontal bottom-offset segment only; it is not the full perimeter or an amount of fabrication labor.

At 0° and zero offset, the model returns a finite 60 × 32 in rectangle. The inclusive angular limit is 45°. Offsets that consume the left end or horizontal span, invalid measurement bases, nonpositive dimensions and numeric overflow are rejected. Dimensions are geometric specifications without kerf, edgework, holes, support design, stock tolerances or installation approval. Glass fabrication and permitted processing must be confirmed with the supplier.