Deck board cut list optimizer

Deck / Layout

Arrange known deck-board cut pieces across mixed stock lengths and existing offcuts, including full saw kerf, end trims and retained remnants.

Enter your inputs

A worked project example is loaded and calculated automatically. Replace the values with your project inputs.

Input notes

Start from required finished pieces in your deck plan, including already approved joints and stagger. Use the same selected length unit for part lengths and stock lengths; blade kerf, end trims and retained-remnant threshold always use inches. Material groups keep different sections, species, grades, finishes or product restrictions apart. All pieces within a group must be interchangeable straight crosscuts.

Each required-part row is group, finished length, quantity. Each stock row is group, actual measured length, quantity or *, new/offcut. An asterisk means unlimited new stock only; existing offcuts require finite quantities. End trims apply to every opened board and already include their own trim kerf. Enter zero only when those ends need no trimming. A separating cut reserves full blade kerf unless the final part exactly reaches the usable end.

The objective first minimizes newly purchased length, then all opened stock length, then opened board count. Existing offcuts have zero new-purchase length. This is not a lowest-price estimate. Up to 16 pieces per group receive exact search, with a shared 60,000-state limit; larger groups compare nine constructive plans. A returned feasible plan is checked for part counts, inventory and material balance. It says optimal only if all exact searches finish; a search failure does not prove that every physical arrangement is impossible.

Choose the option that matches your project.
Each line: material group, finished length, quantity. Separate columns with commas. Use the selected length unit, whole quantities, up to 30 rows, 120 pieces, and 6 groups.
Each line: material group, actual stock length, quantity or *, new or offcut. Separate columns with commas. Use the selected length unit and up to 20 rows. * means unlimited new stock; offcuts need finite whole quantities.
in
Enter blade kerf in inches.
in
Enter left end trim including its kerf in inches.
in
Enter right end trim including its kerf in inches.
in
Enter minimum retained remnant in inches.

About this calculator

A cut list preserves the finished pieces already chosen for a deck layout and assigns them to compatible new stock and existing offcuts, accounting for trims and saw kerf.

Steps

  1. Part and stock length unit

    Choose the option that matches your project.

  2. Required finished parts

    Each line: material group, finished length, quantity. Separate columns with commas. Use the selected length unit, whole quantities, up to 30 rows, 120 pieces, and 6 groups.

  3. Available stock and offcuts

    Each line: material group, actual stock length, quantity or *, new or offcut. Separate columns with commas. Use the selected length unit and up to 20 rows. * means unlimited new stock; offcuts need finite whole quantities.

  4. Blade kerf

    Enter blade kerf in inches.

  5. Left end trim including its kerf

    Enter left end trim including its kerf in inches.

  6. Right end trim including its kerf

    Enter right end trim including its kerf in inches.

  7. Minimum retained remnant

    Enter minimum retained remnant in inches.

Formula

Usable stock = measured length − left trim − right trim; trims already include their own kerf. A pattern of n pieces consumes sum(lengths) + n × kerf when a final cut leaves a remnant, or sum(lengths) + (n−1) × kerf when its last piece exactly reaches the usable end. Do not combine different material groups. Minimize new purchased length first, then all opened stock length, then opened board count. Groups up to 16 pieces receive bounded exact search; larger groups compare nine constructive plans. Optimal is reported only after every exact search completes.

Notation: sum adds the listed values.

Interpret the result

The result distinguishes newly purchased boards from opened offcuts. Its objective minimizes new length first; it does not find the lowest price or change the required joint positions.

Worked example

The existing 72-in offcut fits one 60-in part and leaves 12 in. The remaining 60 + 36 + 36 = 132 in of parts fit one 144-in board; three separating cuts use 0.375 in of kerf, so 132.375 in fits. The result is 1 new board and 1 existing offcut.

Example result: 1 new board; 1 existing offcut

Example inputs
Part and stock length unit
Decimal inches
Required finished parts
A,60,2 A,36,2
Available stock and offcuts
A,144,*,new A,192,*,new A,72,1,offcut
Blade kerf
0.125 in
Left end trim including its kerf
0 in
Right end trim including its kerf
0 in
Minimum retained remnant
10 in

FAQs

Does this optimizer change my board layout?

No. It allocates the finished pieces you enter and does not move the support locations or joints.

What do the layout marks refer to?

Use the stated origin, centerline or face reference, and units shown with the result. Display rounding may differ from the internal coordinates.

Does this approve the selected dimensions or product?

No. It lays out the dimensions you enter and does not establish structural capacity, product cutting permission, or installation compliance.

Additional examples and limits

Cut-list examples and limits

Required parts: two 60-in pieces and two 36-in pieces. Available stock: unlimited new 144/192-in boards and one existing 72-in offcut, all in group A. With 1/8-in kerf, no end trims and a 10-in retained-remnant threshold, one 60-in part fits the existing offcut and the remaining 60 + 36 + 36-in parts fit one new 144-in board. Opened stock totals 216 in: 192 in of finished pieces + 0.5 in kerf + 23.5 in retained remnants. Buying one 192-in board alone cannot supply the four pieces because their finished lengths already total 192 in before the separating cuts.

Boundary: one exact 96-in part in a 96-in stock board needs no separating cut when the ends need no trimming. Two 96-in parts require at least 192.125 in for one 1/8-in separating cut. A 192-in board is insufficient. If the last piece leaves a positive remnant, reserve its full separating kerf too; a tiny leftover shorter than the blade width is not treated as a valid cut under this convention.

Trims include their own trim kerf and reduce both usable ends before planning. Existing material not opened remains inventory, not counted as waste. An end remnant at or above the entered threshold is retained; smaller remnants are discarded without changing the selected objective. Material balance always separates finished lengths, trims, piece kerf and both remnant categories.

These examples follow the calculator's declared cut and inventory conventions; product cutting permission and saw setup must be checked separately. Use at most 30 part rows, 20 stock rows, 120 pieces and 6 groups. Mixed-angle cuts, board rotation, width ripping, defects, joint repositioning, structure, prices and cloud export/storage are excluded. Required lengths may come from the separate deck-board layout tool; this optimizer preserves those requirements and allocates stock instead of selecting a stagger layout.

Prepare board rows and supported joint positions