Deck bearer layout calculator

Deck / Layout

Count bearer lines from a known centerline span, or calculate members, lumber footage and set-out marks from an outside rectangular deck outline.

Enter your inputs

A worked project example is loaded and calculated automatically. Replace the values with your project inputs.

Choose the option that matches your project.
ft
Enter deck span in feet.
ft
Enter bearer spacing in feet.
Choose the option that matches your project.
Limits and notes

Known-span mode uses the distance between the two boundary centerlines. Outside-outline mode uses the overall width across the bearers. Inner and outer set-ins are measured from the deck edge to the outside face of the boundary member. Member length runs along each bearer. A double bearer is two entered thicknesses with no gap. Centers are divided equally at or below the maximum you enter; no allowable spacing or member size is selected.

All outline marks are inches from the inner deck edge. Near-side marks locate the edge of the bearer assembly, while center marks locate its middle. In ledger mode, enter the actual ledger thickness: it replaces the first boundary bearer, and its length is reported separately. Joined stock, splices, housings, slope, connection details and structural design are excluded. Up to 1,000 boundary lines can be displayed; use the numeric marks and verify measurement rounding before transfer.

About this calculator

Bearers are the beams supporting the joists. This calculator counts their lines across a known span using your maximum spacing, including both boundary lines.

Steps

  1. Bearer input

    Choose the option that matches your project.

  2. Deck span

    Enter deck span in feet.

  3. Bearer spacing

    Enter bearer spacing in feet.

  4. Bearing boundary

    Choose the option that matches your project.

  5. Member length (available in another mode)

    Enter member length in feet.

  6. Outside deck width (available in another mode)

    Enter outside deck width in feet.

  7. Actual member thickness (available in another mode)

    Enter actual member thickness in inches.

  8. Inner set-in (available in another mode)

    Enter inner set-in in inches.

  9. Outer set-in (available in another mode)

    Enter outer set-in in inches.

  10. Maximum bearer centers (available in another mode)

    Enter maximum bearer centers in feet.

  11. Bearer members (available in another mode)

    Choose the option that matches your project.

  12. Actual ledger thickness (available in another mode)

    Enter actual ledger thickness in inches.

Formula

outline: boundary centers deduct actual thicknesses and set-ins; intervals = ceil(center span ÷ maximum centers), equally divided. Count one or two members per bearer line; list ledger footage separately. Known-span mode counts both boundary lines or replaces the first with a ledger.

Notation: ceil rounds up to the next whole number.

Interpret the result

The count and any marks follow the selected boundary mode and actual dimensions. They do not establish member sizes or permitted spans.

Worked example

A 16-ft span at an 8-ft maximum gives ceil(16 ÷ 8) = 2 intervals. Including both boundary lines gives 3 bearer lines.

Example result: 3 bearer lines

Example inputs
Bearer input
Known centerline span
Deck span
16 ft
Bearer spacing
8 ft
Bearing boundary
Beams at both boundaries

FAQs

Is the spacing always exactly the maximum I enter?

No. The span is divided into equal intervals at or below the entered maximum.

What do the layout marks refer to?

Use the stated origin, centerline or face reference, and units shown with the result. Display rounding may differ from the internal coordinates.

Does this approve the selected dimensions or product?

No. It lays out the dimensions you enter and does not establish structural capacity, product cutting permission, or installation compliance.

Additional examples and limits

Outside outline to bearer marks

For a 12-ft outside width, 2.5-in actual single members, 4-in set-ins at both edges and an entered maximum of 3 ft: the center span is 144 − 4 − 4 − 2.5 = 133.5 in. Four equal intervals give five bearer lines at 33.375-in centers. Near-side marks are 4, 37.375, 70.75, 104.125 and 137.5 in from the inner deck edge. Five 16-ft members give 80 linear ft before waste or stock-length cuts.

Two 2.5-in members per line give a 5-in assembly, five lines, ten members and 160 linear ft; actual centers become 32.75 in. Replacing the inner boundary with a 1.5-in ledger gives four double-bearer lines, eight members and 128 linear ft, plus a separate 16-ft ledger. Ledger and bearer centerlines use their respective actual thicknesses. These are arithmetic examples, not recommended member sizes or spacings.

Offsets or thicknesses that leave no positive boundary span, or make adjacent assemblies overlap, are rejected. An exact spacing maximum does not add a line; exceeding it does. Different shapes, angled ends, nonidentical member lengths and structural requirements need the relevant project plan.